Thu, Nov 28, 2:05 PM CST

Renderosity Forums / Bryce

All Forums

Welcome to the Bryce Forum

Forum Moderators: TheBryster

Bryce F.A.Q (Last Updated: 2024 Nov 26 4:28 pm)

[Gallery]     [Tutorials]

THE PLACE FOR ALL THINGS BRYCE - GOT A PROBLEM? YOU'VE COME TO THE RIGHT PLACE

Subject: Object file not meshing right in Bryce..

tom271 opened this issue on Feb 28, 2007 · 8 posts
Back to Forum Print
tom271 ( ) posted Wed, 28 February 2007 at 10:08 PM · edited Thu, 28 November 2024 at 11:32 AM

file_370346.jpg

I am working on a  WIP..   everything has been good until this last WIP.. I meshed the model to an object file just like I have been doing.. and I'm getting this... all my settings have been the same... 

is this due to some limit in mesh size.. Obj. 106,24kb..



  ----------------------------------------------------------------------------------------------------------------------------


tom271 ( ) posted Wed, 28 February 2007 at 11:29 PM

I think I already know what happen...  I was using Rhino v4 (EVALUATION) and I was saving in my native v.2 file form...  Well some objects became corrupted...  not everything.....  got to start over..



  ----------------------------------------------------------------------------------------------------------------------------


Death_at_Midnight ( ) posted Wed, 28 February 2007 at 11:48 PM

Greetings Tom271. I take it the objects should've been smooth?

tom271 ( ) posted Thu, 01 March 2007 at 12:07 AM

Hi....

Corrupted objects not the file it self.....  just have to do some stuff again.... 



  ----------------------------------------------------------------------------------------------------------------------------


pakled ( ) posted Thu, 01 March 2007 at 7:00 AM

I think you can mess with smoothing in Bryce (setting the angle, etc), but probably you'd have more control in Rhino. Or failing that, make the edges hard (heck, if Wings can do that, I'm sure Rhino can..;)

I wish I'd said that.. The Staircase Wit

anahl nathrak uth vas betude doth yel dyenvey..;)

tom271 ( ) posted Thu, 01 March 2007 at 1:24 PM

Thanks packle.....  No. Smoothing has nothing to do with it.....   it  just loads in like that...   The problem seemed to be my using  Rhino evaluation V.4 and my saving the work in a v.2 format only. Just a few objects in the model were effected....  No problems were observed In Meshing the work in 3DS format....    just obj. file format gave this result....

Rhino has lots of controls and remedies...  If one way doesn't seem to work there is always another way to skin that Rhino....  (an old Rhino users saying...)



  ----------------------------------------------------------------------------------------------------------------------------


pakled ( ) posted Fri, 02 March 2007 at 9:46 AM

ok...shows what I know about Rhino (other than it's outrageously expensive..;)

I wish I'd said that.. The Staircase Wit

anahl nathrak uth vas betude doth yel dyenvey..;)

tom271 ( ) posted Fri, 02 March 2007 at 3:32 PM

Try out the evaluation v.4..   Rhino is a very logical and it has an easy learning curve...   yes,  it is expensive but get over it...   One bad and terrible thing about Rhino (besides the cost,, my God) is that you'll inherit a bunch of people that will attack you in the jugular vein at the mere mention of NURBs..

I just mentioned it... OH no..    so take cover....  hurry! 



  ----------------------------------------------------------------------------------------------------------------------------


Privacy Notice

This site uses cookies to deliver the best experience. Our own cookies make user accounts and other features possible. Third-party cookies are used to display relevant ads and to analyze how Renderosity is used. By using our site, you acknowledge that you have read and understood our Terms of Service, including our Cookie Policy and our Privacy Policy.