Wed, Dec 25, 11:41 AM CST

Renderosity Forums / Poser - OFFICIAL

All Forums

Welcome to the Poser - OFFICIAL Forum

Forum Coordinators: RedPhantom

Poser - OFFICIAL F.A.Q (Last Updated: 2024 Dec 23 7:38 pm)

Poser Gallery - Poser Freestuff

Subject: Modeling a Diamond? or a Diamond Model?

artposer opened this issue on Nov 10, 2008 · 10 posts
Back to Forum Print
artposer ( ) posted Mon, 10 November 2008 at 4:54 AM · edited Tue, 24 December 2024 at 11:50 PM

I am looking for a tutorial on how to model a daimond. I am using Hexagon 2.5  or know of a model I can purchase or better for free?

JenX ( ) posted Mon, 10 November 2008 at 5:26 AM

Attached Link: http://free.daz3d.com/free_weekly/detail.php?free_id=23

I know DAZ has a free one here ( you have to be signed in to reach their archive).   

Sitemail | Freestuff | Craftythings | Youtube|

Knowledge is knowing a tomato is a fruit. Wisdom is not putting it into a fruit salad.

artposer ( ) posted Mon, 10 November 2008 at 5:34 AM

Thank you Jen

bagginsbill ( ) posted Mon, 10 November 2008 at 6:30 AM

Attached Link: 3D Lapidary

More shapes than you could ever use at the link.

Renderosity forum reply notifications are wonky. If I read a follow-up in a thread, but I don't myself reply, then notifications no longer happen AT ALL on that thread. So if I seem to be ignoring a question, that's why. (Updated September 23, 2019)

sangelico ( ) posted Mon, 10 November 2008 at 6:37 AM

Thanks bagginsbill - I've been trying to remember that link for a couple of years :)

artposer ( ) posted Mon, 10 November 2008 at 6:43 AM

Yes alot of shapes I want to model my own to use in my own products but that gives me a starting point

RedHawk ( ) posted Mon, 10 November 2008 at 8:50 AM · edited Mon, 10 November 2008 at 8:52 AM

Here's a tut on modeling a diamond in Maya.
The steps should be similar in most modeling software.....
http://www.lemiere.com/tutorials/tutorials_diamondmodel.htm

.....and another using Cinema 4D
http://www.jag4d.com/diamond_modeling.html

<-insert words of wisdom here->

Rosemaryr ( ) posted Mon, 10 November 2008 at 9:29 AM

3D Lapidary also has some pages on making the models:
http://www.3dlapidary.com/HTML/Intro3D.htm
about half-way down, shows how I did it before I fully understood how to interpret genuine cutting instructions. 
If you have cutting instructions to follow then look here:
http://www.3dlapidary.com/HTML/Facets.htm
The only difficulty with the latter method, is that the Boolean operations put the normals to the inside, (something I wasn't aware of at the time I wrote the page), so you will have to fix your normals at the end.

RosemaryR
---------------------------
"This...this is magnificent!"
"Oh, yeah. Ooooo. Aaaaah. That's how it starts.
Then, later, there's ...running. And....screaming."

artposer ( ) posted Mon, 10 November 2008 at 10:24 AM

thank you

Daidalos ( ) posted Mon, 10 November 2008 at 9:12 PM

I would suggest going here to if you are willing to buy some.

http://www.renderosity.com/mod/bcs/index.php?vendor=2498

Mertext's set is really inexpensive, turns out some nice looking gems, can be used I think to create your own jewlrey etc....and mertext has some great free mats for them too at his site.

Hope thats of some help to you. If not let me know and I'll wip one up for you for free artposer.


"The Blood is the life!"

 

Privacy Notice

This site uses cookies to deliver the best experience. Our own cookies make user accounts and other features possible. Third-party cookies are used to display relevant ads and to analyze how Renderosity is used. By using our site, you acknowledge that you have read and understood our Terms of Service, including our Cookie Policy and our Privacy Policy.