Thu, Dec 26, 8:09 PM CST

Renderosity Forums / Poser - OFFICIAL

All Forums

Welcome to the Poser - OFFICIAL Forum

Forum Coordinators: RedPhantom

Poser - OFFICIAL F.A.Q (Last Updated: 2024 Dec 26 8:04 pm)

Poser Gallery - Poser Freestuff

Subject: Free/low cost/open source 3d horse model.

Bisto opened this issue on Dec 23, 2005 · 9 posts
Back to Forum Print
Bisto ( ) posted Fri, 23 December 2005 at 9:00 AM · edited Thu, 26 December 2024 at 7:57 PM

Hi, Can anyone suggest a 3d horse model that is Free or low cost. I've looked at the milhorse but don't want to spend too much as I'm only trying to experiment with modeling and poser in general. I've looked on turbosquid,zygote and of course DAZ.Just wondered if anyone else can suggest anywhere else?

thefixer ( ) posted Fri, 23 December 2005 at 12:31 PM

Have you tried the DAZ Charger, relatively low cost and not too bad to use. There's a few images in my gallery with it if you want to have a look! thefixer, poser coord.

Injustice will be avenged.
Cofiwch Dryweryn.

Mystic-Nights ( ) posted Fri, 23 December 2005 at 12:40 PM

Attached Link: http://3dscience.com/free_3d_horse_model.asp

There is an open source horse available by Zygote. Not that it is not boned or rigged, so it is not poseable.

randym77 ( ) posted Fri, 23 December 2005 at 9:29 PM

The 3dScience horse is the Poser 4 horse. Only not rigged for Poser. Not rigged at all, so you can't pose it. But if you want to learn to rig, check it out!

freyfaxi ( ) posted Sat, 24 December 2005 at 12:08 AM · edited Sat, 24 December 2005 at 12:09 AM

If you're using poser..you already should HAVE a horse ? And there are lots, and lots of freebies availible for it as well ?

Message edited on: 12/24/2005 00:09

Bisto ( ) posted Sat, 24 December 2005 at 4:20 AM

Hi, Thanks for all the suggestions and comments. I'll try using the Poser 4 horse to start with a see how far I get. Thanks again.

Tiny ( ) posted Sat, 24 December 2005 at 7:02 AM

At planit3d.com there are very nice morphs for the P4 horse!

At the site select '/Downloads/Poser/Injections & Morphs'.


odeathoflife ( ) posted Sun, 25 December 2005 at 2:15 AM

so does zygote releaseing the mesh as a os mesh release the poser horse from (C) this is a little confusing ;~

♠Ω Poser eZine Ω♠
♠Ω Poser Free Stuff Ω♠
♠Ω My Homepage Ω♠

www.3rddimensiongraphics.net


 

randym77 ( ) posted Sun, 25 December 2005 at 1:42 PM

No. The open source horse is only the solid mesh. Basically, it's a horse prop. You would have to group and rig it to make it posable. If you do that, you can distribute it, but you can't distribute the Poser version.

Privacy Notice

This site uses cookies to deliver the best experience. Our own cookies make user accounts and other features possible. Third-party cookies are used to display relevant ads and to analyze how Renderosity is used. By using our site, you acknowledge that you have read and understood our Terms of Service, including our Cookie Policy and our Privacy Policy.